Buying Guide
Aluminium anodising is an electrochemical process, and the specification decides whether you need Type II or Type III
Anodising grows an aluminium oxide layer into the surface of the part rather than laying a coating on top of it, and the layer does not peel. Type II sulphuric anodising is the general-purpose route for corrosion resistance, appearance and electrical insulation; Type III hard anodising builds a thicker, harder layer for wear and hard-surface requirements.
The buyer's job is to fix three things: which type you need, which alloy the part is made from, and what the finished surface has to do. Fukar runs Type II and Type III anodising from Shah Alam under ISO 9001:2015 quality management, with MIL-A-8625F as the referenced process standard.
This guide sets out what to put on the drawing, what the process can and cannot change on the part, and what inspection evidence to ask for with the delivery.
Process Selection
Type II Sulphuric Anodising vs Type III Hard Anodising
Both types are electrochemical processes run to MIL-A-8625F. They differ in the thickness and character of the oxide layer, and that difference decides where each one is used.
Discuss Your Spec| Attribute | Type II (Sulphuric) | Type III (Hard) |
|---|---|---|
| Oxide character | Standard porous oxide layer | Thicker, denser oxide layer |
| Primary reason to specify | Corrosion resistance, appearance and electrical insulation | Surface hardness and wear resistance |
| Finished surface | Can be dyed before sealing; the seal option sets the final corrosion behaviour | Sealed to close the pores and harden the surface |
| Typical use | Electronics housings, aluminium brackets, precision machined parts, industrial aluminium components | Parts exposed to abrasion and repeated contact |
| Electrical property | Non-conductive oxide layer (application dependent) | Non-conductive oxide layer (application dependent) |
| Standard reference | MIL-A-8625F (project-specific requirements) | MIL-A-8625F (project-specific requirements) |
What Changes on the Part
Alloy, Finish and Dimensional Impact
Alloy selection
The alloy decides how the oxide behaves, so the alloy has to be stated on the drawing. Chemistry and dwell time are then set for the material you actually supply.
Finish and seal
Decorative colour, where it is required, is applied before sealing. The seal is not a cosmetic choice: it closes the pores in the oxide and sets how the finished surface behaves in service.
What anodising cannot change
Anodising grows the surface into the part, so it changes dimensions. A part that has to hold a tight fit, or that lands on a machined sealing face, needs that allowance stated before the order is placed.
Technical Reference
Anodising Specification Snapshot
Anodising selection depends on alloy, required oxide thickness, dye and seal requirements, and operating environment. Requirements are confirmed during technical review before production.
Discuss Your Spec| Parameter | Typical Reference |
|---|---|
| Primary Standard | MIL-A-8625F (project-specific requirements) |
| Anodising Types | Type II (sulphuric) / Type III (hard anodising) |
| Thickness Range | Type II and Type III ranges by requirement |
| Electrical Property | Non-conductive oxide layer (application dependent) |
| Typical Use | Electronics housings, aluminium brackets, precision machined parts, industrial aluminium components |
How It Works
The Aluminium Anodising Process Flow
1. Degrease & Rinse
Alkaline and emulsion degreasing removes cutting oils, drawing lubricants and shop soils before the part enters the bath.
2. Etch & Desmut
Surface conditioning and desmutting prepare the aluminium so the oxide layer forms consistently over the whole part.
3. Anodise
The part is anodised under controlled conditions so the oxide grows to the thickness and the type called out on the drawing.
4. Dye & Seal
Where colour is specified, the dye is applied before sealing, and the seal closes the pores in the oxide.
5. Rinse & Dry
Parts are rinsed and dried under controlled handling so the finished surface is not marked in transit.
6. Inspect & Certify
Coating thickness, appearance and process compliance are checked before the batch is released.
Drawing Notes
What to Put on the Drawing for Anodised Parts
A complete anodising instruction names the alloy, the type, the oxide thickness with its tolerance, the colour and seal requirement, the areas to mask, and the inspection the buyer wants recorded. Anything left open at RFQ stage is where anodising disputes start.
Ask what is delivered with the parts. A certificate of conformance recording the process, the measured thickness and the seal treatment gives your QA team something to check the batch against, and it is easier to agree that at order stage than at goods-in.
Before You Order
Aluminium Anodising Buyer Checklist
Six things to confirm on the drawing or RFQ, so the job is quoted and run without a clarification loop.
Material and alloy
- Anodising applies to aluminium and its alloys. State the alloy designation on every part, because the alloy drives how the oxide forms.
- State whether the part is machined, cast or extruded, and the surface finish the aluminium arrives with.
- If the part is a precision component with a controlled fit, flag the surfaces that must be masked or excluded from anodising.
Film build and finish
- State the anodising type: Type II sulphuric or Type III hard, and the oxide thickness with its tolerance.
- State the colour requirement, if any, and the seal treatment to be applied.
- For fitted parts, say whether the thickness is measured before or after any further machining.
Common defects to watch
- Uneven or patchy colour usually points to uneven pre-treatment or a variation in bath condition.
- Poor adhesion of a dye or a topcoat traces back to sealing that was not carried out as specified.
- Burning on high-current areas shows as a burnt or bleached surface, and it is a current-density problem rather than a material one.
Inspection and evidence
- MIL-A-8625F is the referenced process standard for aluminium anodising at Fukar, with project-specific requirements accommodated.
- Coating thickness is verified on each batch at the points your drawing calls out.
- Ask for the certificate of conformance recording the process, the measured thickness and the seal treatment.
Common Questions
Aluminium Anodising FAQ
Answers to the specification and process questions buyers ask most often about aluminium anodising.
Ask a Technical QuestionWhat is aluminium anodising?
Aluminium anodising is an electrochemical process that converts the surface of aluminium into a durable aluminium oxide layer. The oxide grows into the metal surface rather than sitting on top of it, so it does not peel, and it improves corrosion resistance, surface hardness and paint adhesion at the same time.
What is the difference between Type II and Type III anodising?
Type II is the general-purpose sulphuric route, used for standard corrosion protection, appearance and electrical insulation, and it can be dyed before sealing. Type III hard anodising builds a thicker, denser oxide layer and is specified where surface hardness and wear resistance are the requirement.
Which standard is used for aluminium anodising?
MIL-A-8625F is the process standard referenced for aluminium anodising at Fukar, with project-specific requirements accommodated where a drawing calls for something more particular.
Does anodising change the size of a part?
Yes. Anodising grows the surface into the part, so it adds a measurable layer and changes the dimensions. That is why the oxide thickness and the masking of critical surfaces belong on the drawing, and why precision parts are often better served by a passivation route.
What should I request with anodised parts?
Ask for a certificate of conformance recording the process, the measured coating thickness and the seal treatment, and confirm that the appearance was checked against the approved sample before the batch was released.
Related Pages
Surface Treatment Services Hub
Explore anodising, phosphating and passivation options with surface treatment selection guidance.
View hub →Anodising
See the anodising service, its Type II and Type III capability and the specification snapshot.
View service →Aluminium Passivation
Compare the chemical conversion route for aluminium where dimensional change is not acceptable.
View service →Need anodising support for your aluminium components?
Share your alloy, the anodising type and the performance you need from the surface. We'll review the requirement and confirm the route before production.