Skip to main content
Email us : sales@fukar.com.my

Chroming Services Near Me: Process and Buying Guide

Chroming

Chroming covers two entirely different processes, and the word on the purchase order does not tell you which one you need

Hard chromium plating is a thick electro-deposited chrome coating, specified to AMS 2460 for hydraulic rods, tooling and wear surfaces, where the job is to put a hard, wear-resistant layer back onto a part. Chromate conversion — chromating — is a thin chemical conversion coating applied over an electroplated zinc layer to DIN 50962, where the job is to protect and finish the zinc.

The two have very little in common apart from the word. One is a wear surface, the other is a corrosion treatment on a zinc coating, and the process, the inspection and the specification are entirely different.

Fukar runs both routes from the Shah Alam facility: hard chrome plating to AMS 2460, and trivalent chromate conversion in clear, blue, yellow and black on electroplated zinc under DIN 50962.

Plated fasteners after passivation, inspected before release

Process Selection

Hard Chromium Plating vs Chromate Conversion

The two processes that answer to the word chroming, set out side by side so the right one is chosen the first time.

Discuss Your Spec
Attribute Hard Chromium Plating Chromate Conversion (Chromating)
What it is An electro-deposited chromium coating built to a specified thickness A chemical conversion coating formed on an electroplated zinc surface
Standard AMS 2460 — Chromium Plating (Hard) DIN 50962 — Chromate Conversion Coatings on Electroplated Zinc
Substrate Steel parts selected for a hard wear surface Electroplated zinc (Fe/Zn)
What it is for Hydraulic, tooling and wear surfaces European-spec fasteners and components
Appearance Bright metallic chrome deposit Trivalent chromate in clear, blue, yellow or black
Environmental and export note Specified against the drawing requirement All trivalent chromate options are referenced under RoHS and REACH for EU export and electronics work
Typical use Hydraulic rods, tooling, wear surfaces Fasteners and components where a trivalent chromate finish is specified

Choosing

Which of the Two You Actually Need

You need hard chrome when the part wears

Hard chromium plating is specified where a dimension has to be restored or a surface has to carry wear: hydraulic rods, tooling and wear surfaces. The drawing should state the surface to be coated, the thickness and the areas to mask.

You need chromating when the part is zinc plated

Chromate conversion is applied over an electroplated zinc layer. If your drawing says zinc plating with a clear, blue, yellow or black chromate finish, that is the DIN 50962 route, not a chrome coating.

Decorative chrome is not part of this range

Hard chrome plating to AMS 2460 is the only chromium plating route here. Chrome plating for appearance on trim or consumer parts is not a service Fukar offers, so it is worth confirming which of the two processes a supplier means before you order.

Specification

How Hard Chromium Is Specified

A hard chrome drawing normally names the surface or surfaces to be coated, the thickness required on each, the areas to be masked, and the standard the coating is run to. AMS 2460 is the reference for the process.

Chrome is hard and it is deposited on the surface, so the growth has to be allowed for on any fit, seal or bearing surface. That is why masking and the affected dimensions belong on the drawing at RFQ stage rather than being worked out during production.

Specification

How Chromating Is Specified

A chromate conversion instruction names the underlying zinc coating and its standard, the colour of the chromate, and the standard for the conversion layer itself. DIN 50962 covers chromate conversion coatings on electroplated zinc, and the trivalent options are the ones referenced under RoHS and REACH for work going to EU markets or into electronics supply chains.

RoHS and REACH compliance is a property of the chemistry used, not of a supplier's willingness. State the requirement on the order and it is answered with the specified trivalent route.

Technical Reference

Chromate Conversion on Electroplated Zinc

The zinc layer and the conversion layer are specified separately, because they do different jobs.

Discuss Your Spec
Parameter Typical Reference
Underlying coating Zinc (Fe/Zn) to ASTM B633, with 5–12 µm common thickness per specification
Conversion standard DIN 50962 — Chromate Conversion Coatings on Electroplated Zinc
Chromate options Trivalent chromate: clear, blue, yellow or black
Environmental and export note RoHS / REACH — Restriction of Hazardous Substances, applied to all trivalent chromate options for EU export and electronics work
Corrosion evidence Per-batch ASTM B117 salt spray test report
Typical use European-spec fasteners and components

Before You Order

Chroming Specification Checklist

Six things to confirm on the drawing or RFQ, so the job is quoted and run without a clarification loop.

Material and strength

  • State the substrate. Hard chrome is applied to steel parts; chromate conversion is applied over an electroplated zinc surface.
  • Confirm the zinc coating standard and thickness where the drawing calls for a chromated zinc finish.
  • State the tensile strength where the part is high-strength steel, because bake embrittlement relief is mandatory for steel at or above 1,000 MPa on acid-plated finishes.

Process type and thickness

  • Say which process is meant: hard chromium plating to AMS 2460, or chromate conversion to DIN 50962.
  • For hard chrome, state the thickness on each coated surface and the areas to mask.
  • For chromating, state the chromate colour required and the standard for the underlying zinc coating.

Common defects to watch

  • Thin or uneven coverage on the working surface of a hard chrome part points to insufficient build or poor current distribution.
  • Peeling or poorly adherent chrome usually traces back to inadequate preparation of the steel surface.
  • Patchy or weak colour on a chromated part points to a conversion bath that was not at condition, or to contamination of the rinse.

Inspection and evidence

  • AMS 2460 is the reference for hard chromium plating, and DIN 50962 the reference for chromate conversion coatings on electroplated zinc.
  • Thickness is verified on each batch at the points your drawing calls out.
  • A certificate of conformance records the process and the finish, and salt spray test reports are issued per batch where ordered.

Common Questions

Chroming Services FAQ

Answers to the questions buyers ask when a drawing or a purchase order says only 'chromed'.

Ask a Technical Question
What is chroming?

Chroming is used for two separate processes in industry. Hard chromium plating is an electro-deposited chrome coating built to a specified thickness for wear surfaces and dimensional restoration, specified to AMS 2460. Chromate conversion, or chromating, is a thin chemical conversion coating applied over an electroplated zinc layer, specified to DIN 50962 for corrosion protection and finish.

How do I know whether I need hard chrome or chromating?

Look at what the coating sits on and what it is for. If the drawing specifies a wear surface, a hydraulic rod or a tooling surface, it is hard chromium plating. If it specifies a zinc coating with a clear, blue, yellow or black chromate finish, it is chromate conversion on the zinc.

Does Fukar provide decorative chrome plating?

No. Hard chromium plating to AMS 2460 is the only chromium plating process Fukar runs, for hydraulic, tooling and wear surfaces. Chrome plating for appearance on trim and consumer parts is not part of the range, so it is worth confirming which of the two processes a supplier means before an order is placed.

Which chromate options are available and are they RoHS compliant?

The chromate conversion options are trivalent, in clear, blue, yellow and black, applied over electroplated zinc under DIN 50962. All trivalent chromate options are referenced under RoHS and REACH, which is the point to state on orders for EU export and electronics work.

How is a chromed or chromated part inspected?

Thickness is verified on each batch at the points the drawing calls out, and appearance is checked against the approved sample. A certificate of conformance records the process and the finish, and salt spray test reports are issued per batch against the specification ordered.

Surface Treatment Services Hub

Explore anodising, phosphating, passivation and surface preparation options.

View hub →

Electroplating Services Hub

View zinc, zinc nickel and electroless nickel services with process comparison guidance.

View hub →

Aluminium Passivation

See the chemical conversion routes for aluminium and how they differ from anodising.

View service →

Need chroming support for your parts?

Send the drawing or the specification line and the substrate. We'll confirm whether the part calls for hard chrome plating or chromate conversion, and quote the right route.