Nickel Coatings
Nickel plating comes in two distinct forms, and the right one depends on the part and the standard on your drawing
Fukar's nickel capability sits in two places: zinc nickel alloy plating to ASTM B841, an electrodeposited coating for steel fasteners in severe service, and electroless nickel plating to MIL-C-26074 and AMS 2404, a chemically deposited coating used where uniform coverage of complex geometry matters.
Buyers often arrive with a drawing that says only 'nickel plate'. The first job is to establish which of the two routes is actually meant, because the deposit, the thickness range, the substrate handling and the inspection evidence are all different.
Both processes are run from the Shah Alam facility under ISO 9001:2015 quality management, with thickness and composition verified on every batch and a certificate of conformance issued for the job.
Technical Reference
Zinc Nickel Plating vs Electroless Nickel Plating
Both are nickel-bearing coatings and both are applied at Fukar, but they are different processes, for different parts, under different standards.
Discuss Your Spec| Attribute | Zinc Nickel Plating | Electroless Nickel Plating |
|---|---|---|
| Standard | ASTM B841 | MIL-C-26074; AMS 2404 for mid-phosphorus |
| How it is applied | Electrodeposited in a zinc-nickel alloy bath | Chemical deposition with no external current |
| Common thickness | Typically 8–15 µm (per specification) | Typically 5–25 µm |
| Alloy or phosphorus | Typically 12–15% nickel | Not an alloy deposit — phosphorus class is low, medium or high, by requirement |
| Corrosion evidence | Per-batch ASTM B117 salt spray test report | Application-dependent performance, with the test method set by specification |
| Typical use | Brake components, underbody fasteners, fuel system hardware, severe-duty industrial fasteners | Connectors, PCB hardware, valves, precision-machined parts, oil and gas components |
Specification Clarity
How to Read the Phrase on Your Drawing
'Nickel plate', full stop
Where a drawing or purchase order simply says nickel plating, the route has to be established before the job is quoted. Send the full specification line and the substrate, and the route will be confirmed against the standard and the thickness called out.
Zinc nickel, when the part is steel
Zinc nickel plating is the route selected for steel fasteners in severe service — brake and underbody hardware, fuel system fixings and heavy-duty industrial fasteners — where an alloy coating and a bake for embrittlement relief are part of the specification.
Electroless nickel, when coverage is the problem
Electroless nickel is selected where uniform thickness on blind holes, internal bores, sharp edges and complex machined geometry matters, and where soldering, wear or dimensional stability drive the choice.
Precision Work
Why Electroless Nickel Is Chosen for Precision Parts
Electroless nickel is deposited without an external current, so the coating builds evenly over complex geometry rather than thinning where the current struggles to reach. That is why it is the usual answer for blind holes, internal bores, sharp edges and precision-machined parts.
Phosphorus content is the other variable. Mid phosphorus is used for general wear performance, and high phosphorus is chosen where solderability and corrosion resistance matter more. The class is set by the requirement rather than by preference.
On hardened tool steel, the preparation route is mechanical or alkaline rather than acid pickling, which keeps hydrogen pickup away from the part — which matters for precision components that have to keep their properties.
Technical Reference
Electroless Nickel Specification Snapshot
Electroless nickel selection depends on the phosphorus class, the thickness the part needs and the geometry it has to cover.
Discuss Your Spec| Parameter | Typical Reference |
|---|---|
| Primary Standard | ASTM B733 / project-specific customer requirements |
| Standards in the Range | MIL-C-26074 and AMS 2404 |
| Common Thickness Range | Typically 5–25 µm |
| Phosphorus Class | Low, medium or high, by requirement |
| Salt Spray Benchmark | Application-dependent performance, with the test method set by specification |
| Typical Use | Connectors, PCB hardware, valves, precision-machined parts, oil and gas components |
Hydrogen Management
Bake Embrittlement Relief and Hydrogen Control
Zinc nickel plating is an electrodeposited process, so hydrogen pickup has to be managed on high-strength steel. Bake embrittlement relief is mandatory for steel at or above 1,000 MPa, and Fukar bakes every zinc nickel job on hardened steel as standard, with the bake record forming part of the certificate of conformance.
On acid-plated finishes the bake is run at 190–220 °C for 4–24 hours within 4 hours of plating. Where the customer specification calls for the bake on other finishes, it is included on that basis too.
Electroless nickel handles the issue differently. Because the preparation for hardened tool steel is mechanical or alkaline rather than acid pickling, hydrogen damage is limited at the point where it would otherwise be introduced.
Before You Order
Nickel Plating Specification Checklist
Six things to confirm on the drawing or RFQ, so the job is quoted and run without a clarification loop.
Material and strength
- State the substrate and its grade. Zinc nickel plating is a steel route, and the electroless nickel chemistry is selected for the alloy and the geometry.
- State the tensile strength. At or above 1,000 MPa, bake embrittlement relief is mandatory on acid-plated finishes.
- On hardened tool steel, electroless nickel avoids acid pickling and uses mechanical or alkaline preparation instead, to limit hydrogen damage.
Thickness and finish
- State the coating thickness per surface with its tolerance, and say whether it is measured before or after any further machining.
- For electroless nickel, state the phosphorus class required: low, medium or high.
- For zinc nickel, state the nickel content band and the post-treatment: trivalent chromate or a topcoat.
Common defects to watch
- Thin coverage inside blind holes, bores and sharp edges points to a part that was not agitated properly for the deposit to reach every surface.
- Dull, patchy or dark deposits usually mean the bath was out of balance or the surface was not activated.
- Burning on high-current areas shows as dark deposits along edges and outer surfaces.
Inspection and evidence
- Thickness is verified by XRF or magnetic measurement on each batch, at the points your drawing calls out. XRF also confirms nickel content on zinc nickel.
- A certificate of conformance records the process, the measured thickness, the alloy or phosphorus class, and the bake step where it applies.
- Salt spray test reports are issued per batch against the specification ordered.
Common Questions
Nickel Plating Services FAQ
Answers to the specification and process questions buyers ask most often about nickel coatings.
Ask a Technical QuestionWhat nickel plating services are available in Malaysia?
Fukar's nickel capability covers zinc nickel alloy plating to ASTM B841 and electroless nickel plating to ASTM B733, MIL-C-26074 and AMS 2404. Zinc nickel is used on steel fasteners in severe service; electroless nickel is used on connectors, PCB hardware, valves, precision-machined parts and oil and gas components.
What is the difference between zinc nickel plating and electroless nickel plating?
Zinc nickel plating is electrodeposited in a zinc-nickel alloy bath and is specified for steel fasteners in severe service, typically at 12–15% nickel and 8–15 µm. Electroless nickel is deposited chemically without an external current, which gives uniform coverage on complex geometry, and is specified by phosphorus class at typically 5–25 µm.
Which nickel coating should I choose for a machined part with blind holes?
Electroless nickel. Because it is deposited without an external current, it builds evenly over blind holes, internal bores and sharp edges, where an electrodeposited coating would thin out.
How is nickel plating corrosion performance verified?
For zinc nickel plating, Fukar issues a per-batch ASTM B117 salt spray test report against the specification ordered. For electroless nickel, performance is application-dependent and the test method is set by the specification, so the method and the target are confirmed against your requirement before production.
Is bake embrittlement relief required for nickel plating?
Bake embrittlement relief is mandatory for steel at or above 1,000 MPa on acid-plated finishes, and Fukar bakes every zinc nickel job on hardened steel as standard, with the bake record included in the certificate of conformance. Electroless nickel on hardened tool steel avoids the acid pickling step altogether.
Related Pages
Electroplating Services Hub
View zinc, zinc nickel and electroless nickel services with process comparison guidance.
View hub →Electroless Nickel Plating
See the electroless nickel service, its process steps and its specification snapshot.
View service →Zinc Nickel Plating
See the zinc nickel service, the 12–15% nickel band and the ASTM B841 reference.
View service →Need nickel plating for your components?
Send the material, the geometry and the standard on your drawing. We'll confirm the route and the inspection evidence before production.