Skip to main content
Email us : sales@fukar.com.my

Aluminium Passivation and Chromating Guide

Aluminium Surface Treatment

Aluminium passivation and chromating are chemical conversion treatments, and the route is set by the specification and the environmental requirement

Both processes work on the same principle: the surface of the aluminium is chemically converted rather than coated on top. Passivation restores and stabilises the part's natural corrosion resistance; chromating forms a chromate conversion coating with its own protective and visual characteristics.

On aluminium, chromate conversion is one of the passivation routes Fukar runs, alongside trivalent passivation. Which one is used is decided by the customer specification and the environmental requirements, and it is stated on the order rather than assumed.

The third option buyers often confuse with both is anodising, which is an electrochemical process with a very different result. This guide sets the three apart and shows what to ask for.

Aluminium components after chemical conversion treatment and rinsing

Process Selection

Aluminium Passivation, Chromating and Anodising Compared

Three processes that all end up on aluminium, and the very different results each one produces.

Discuss Your Spec
Attribute Aluminium Passivation Chromating on Aluminium Anodising
Process type Chemical immersion conversion coating Chemical immersion conversion coating Electrochemical anodising — MIL-A-8625F, Type II and Type III
Substrate Aluminium and aluminium alloys Aluminium and aluminium alloys Aluminium and aluminium alloys
Effect on dimensions Negligible thickness build, so it suits tight-tolerance parts Negligible thickness build, so it suits tight-tolerance parts Builds an oxide layer into the surface, so dimensions change
Surface produced Thin, stable conversion layer Chromate conversion coating Integral oxide layer — Type II general purpose or Type III hard
How the route is chosen Customer specification and environmental requirements Customer specification and environmental requirements The performance requirement: corrosion resistance, electrical insulation or wear resistance
Typical use Corrosion support, and preparation for painting or bonding Where a chromate conversion coating is called for on aluminium Electronics housings, aluminium brackets, precision machined parts, industrial aluminium components

Route Selection

How the Route Is Chosen

Start with the specification

If the customer specification names a chrome or chromate conversion coating, that is the route. It is a specification-led decision rather than a preference, and the supplier's job is to run the route that is written down.

Then check the environmental requirement

Where the work goes to EU export or electronics supply chains, the chemistry is chosen to suit that requirement. Fukar runs trivalent passivation and trivalent chromate conversion, and all trivalent chromate options are referenced under RoHS and REACH.

Then check what the part does next

A part that will be painted, bonded or sealed needs a conversion layer that gives the downstream process something to key onto. A part that has to keep its dimensions needs a chemical route rather than anodising.

Drawing Notes

What to State on an Aluminium Passivation Order

The notes that make the route, and the evidence that comes with it, unambiguous.

Discuss Your Spec
Order note What it settles
Alloy designation The chemistry and dwell time are set against the alloy, so the material has to be stated for every part
Process route Chromate conversion or trivalent passivation, as named in the customer specification
Downstream requirement Whether the part is to be painted, bonded, sealed or left as a finished surface
Environmental requirement The export or electronics requirement the chemistry has to meet, such as RoHS and REACH where trivalent chromate is called for
Inspection evidence The coating or weight check to be recorded, and the certificate of conformance required with the delivery

Questions to Ask

What to Ask Your Supplier

Ask which route will actually be run on your parts, and whether it is the route written in your specification. The answer should name the chemistry and the standard, not simply say 'passivation'.

Ask what the delivery documentation records. A certificate of conformance stating the route used, the process parameters and the inspection results gives your QA team something to check the batch against.

Ask how dimensional control is handled. Chemical conversion adds negligible thickness, which is the reason passivation is often preferred over anodising on precision parts, and it is worth confirming against your own tolerances.

Comparison

How Passivation Differs from Anodising in Service

Anodising converts the surface electrochemically and grows an integral oxide layer into the part. It does not peel, it improves corrosion resistance and paint adhesion, and Type III builds a hard surface for wear. But it changes the dimensions of the part, which is the decision point for precision components.

Passivation is a chemical immersion treatment. It leaves the dimensions effectively unchanged, restores the natural passive condition of the aluminium, and prepares the surface for painting or bonding. Where the part has to hold a fit, that difference decides the route.

Before You Order

Aluminium Passivation and Chromating Checklist

Six things to confirm on the drawing or RFQ, so the job is quoted and run without a clarification loop.

Material and alloy

  • State the alloy designation for every part. Common alloys include 6061, 6063, 7075 and casting alloys, and the chemistry is adjusted to the alloy and the customer specification.
  • Confirm the surface finish the aluminium arrives with, and whether the part is machined, cast or extruded.
  • Flag any part that has to hold a fit or a sealing surface, because the route is chosen against the dimensional requirement.

Process route and film build

  • Name the route: chromate conversion or trivalent passivation, as written in the customer specification.
  • State the downstream requirement — painting, bonding, sealing or a finished surface — so the preparation matches it.
  • State the environmental requirement where the work is exported or goes into electronics supply chains.

Common defects to watch

  • Uneven or patchy conversion coating usually points to a deoxidising or rinsing step that was incomplete before immersion.
  • A dull, inconsistent finish across a batch points to bath condition or rinse water quality that drifted during the run.
  • Staining or tide marks are worth flagging before the batch is scheduled, since they are difficult to assess after packing.

Inspection and evidence

  • Ask what is measured to confirm the coating is present and correct — a coating weight or an equivalent check recorded against the specification.
  • Ask for the certificate of conformance recording the route used and the inspection results for the batch.
  • Ask for the process parameters and inspection records to accompany the delivery, where your quality system requires them.

Common Questions

Aluminium Passivation and Chromating FAQ

Answers to the route, specification and inspection questions buyers ask about aluminium conversion treatments.

Ask a Technical Question
What is aluminium passivation?

Aluminium passivation is a chemical surface treatment that forms a thin, stable conversion layer on the surface of aluminium and its alloys. It restores and stabilises the part's natural corrosion resistance, prepares the surface for painting or bonding, and adds negligible thickness, which is why it suits precision components.

What is chromating on aluminium?

Chromating is a chromate conversion coating applied to aluminium by chemical immersion. On aluminium it is one of the passivation routes rather than a separate process family, and which route is used depends on the customer specification and the environmental requirements.

Is aluminium passivation the same as anodising?

No. Anodising is an electrochemical process that grows an integral oxide layer into the part, so it changes dimensions and can be specified as Type II general purpose or Type III hard for wear resistance. Passivation is a chemical immersion treatment that adds negligible thickness and does not change the part's dimensions.

Which aluminium passivation route should I specify?

Specify the route named in your own customer specification. Where the requirement is a chrome or chromate conversion coating, the chromate route is the one to run, and where a trivalent chemistry is called for, the trivalent route is used. Confirm the environmental requirement at the same time, particularly for EU export and electronics work.

What evidence should I request with a passivated or chromated part?

Ask for the certificate of conformance recording the route used and the inspection results, together with the process parameters and inspection records your quality system requires. Confirm what is measured to verify the conversion coating is present and correct before the batch is released.

Surface Treatment Services Hub

Explore anodising, phosphating, passivation and surface preparation options.

View hub →

Aluminium Passivation

See the aluminium passivation service, its routes and the process steps.

View service →

Anodising

Compare the electrochemical route with the chemical conversion route on aluminium.

View service →

Need aluminium passivation or chromating support?

Send the alloy, the route named in your specification and the downstream requirement. We'll confirm the process and the documentation that ships with the batch.