Skip to main content
Email us : sales@fukar.com.my

Zinc Nickel Plating Appearance and Alloy Guide

Alloy and Appearance

A zinc nickel plating finish is set by three numbers and one reference: the nickel band, the thickness, the post-treatment and the standard

Zinc nickel plating is an alloy deposit rather than a single metal layer, and that is why it behaves differently from zinc plating both in service and on the bench. The alloy content is typically controlled at 12–15% nickel and the coating thickness typically at 8–15 µm, with the post-treatment deciding the final appearance and the corrosion response.

The appearance a buyer receives is therefore a consequence of the specification, not an accident of the bath. Change the nickel band, the thickness or the post-treatment and the finish changes with it, which is why the drawing has to fix all three.

Fukar runs zinc nickel plating to ASTM B841 from the Shah Alam facility, with thickness and alloy composition verified on every batch by XRF and a certificate of conformance issued for the job.

Zinc nickel plated fasteners after alloy plating and passivation

Technical Reference

Zinc Nickel Plating Specification Snapshot

Zinc nickel selection depends on the nickel band, the thickness, the post-treatment and the service environment. Requirements are confirmed during technical review before production.

Discuss Your Spec
Parameter Typical Reference
Primary Standard ASTM B841 (project-specific classes as required)
Nickel Content Typically 12–15%
Common Thickness Range Typically 8–15 µm (per specification)
Post-Treatment Trivalent chromate or a topcoat, as specified
Corrosion Evidence Per-batch ASTM B117 salt spray test report
Typical Use Brake components, underbody fasteners, fuel system hardware, severe-duty industrial fasteners

What Changes the Result

How Alloy Content and Finish Change the Deposit

The nickel band

The nickel content is the defining variable in a zinc nickel deposit. Around the 12–15% band the deposit behaves as a controlled alloy, with the electrochemical and elevated-temperature performance that severe-duty fasteners are specified for.

The post-treatment

Trivalent chromate or a topcoat changes both the appearance and how the surface responds to wear and exposure. The choice is made on the drawing, and it is why two zinc nickel parts of the same thickness can look and perform differently.

The thickness

Thickness is the build on the surface, set per specification. On threaded fasteners it is stated before or after the thread, and the measurement points are called out so the reading is taken where the drawing expects it.

Drawing Notes

What to State on a Zinc Nickel Drawing

Six notes that remove the most common ambiguity from a zinc nickel order.

Discuss Your Spec
Drawing note What it settles
Nickel content band The alloy band the deposit has to fall inside, so composition is checked as a pass or fail and not merely reported
Coating thickness and tolerance The build on each surface, and the measurement points, including whether thickness is stated before or after the thread
Post-treatment Trivalent chromate, a topcoat or both, and the colour or finish required where it is specified
Corrosion target and test method The corrosion target in hours to white / red rust and the method used, so the per-batch report is issued against your own requirement
Bake embrittlement relief Whether a bake is required, and the record to be issued with the batch
Appearance reference The approved sample the finish is judged against

Hydrogen Management

Hydrogen Management on High-Strength Fasteners

Zinc nickel plating is electrodeposited, so hydrogen pickup has to be managed on high-strength steel. Bake embrittlement relief is mandatory for steel at or above 1,000 MPa, and Fukar bakes every zinc nickel job on hardened steel as standard, with the bake record forming part of the certificate of conformance.

On acid-plated finishes the bake is run at 190–220 °C for 4–24 hours within 4 hours of plating. Where the customer specification calls for the bake on other finishes, it is included on that basis too.

Inspection

Appearance and Composition Checks on the Batch

Appearance is checked against the approved sample before the batch is released, so a part that does not match the reference is caught at inspection rather than at assembly. That is why the reference sample matters, and why it should be agreed before the order is scheduled.

Composition is checked alongside thickness. XRF confirms both on every batch, and composition is what separates a pass from a fail on a zinc nickel part — a deposit at the right thickness but outside the nickel band is not a conforming part.

Before You Order

Zinc Nickel Plating Specification Checklist

Six things to confirm on the drawing or RFQ, so the job is quoted and run without a clarification loop.

Material and strength

  • Zinc nickel plating suits steel, and it is the usual choice on high-strength fasteners where hydrogen embrittlement risk has to be managed.
  • State the tensile strength and whether a bake is required. Fukar bakes every zinc nickel job on hardened steel as standard, and the bake record is part of the certificate of conformance.
  • Aluminium, copper and brass run in a separate bath with a separate pre-treatment, so confirm the material before quoting.

Alloy and thickness

  • State the nickel content band, the thickness per surface and the tolerance. 12–15% nickel is the common band for severe duty.
  • Name the post-treatment: trivalent chromate, a topcoat, or both.
  • Define the corrosion target in hours and the test method, or state that the coating is for appearance and wear only.

Common defects to watch

  • Dull, patchy deposits usually mean the activation step was short or the bath was out of balance.
  • Peeling points to inadequate cleaning or a missed activation strike.
  • Burning on high-current areas shows as dark deposits along edges and outer surfaces.

Inspection and evidence

  • ASTM B841 defines the coating class, thickness and composition bands for the job.
  • XRF confirms both thickness and nickel content on every batch. Composition, not just build, is what separates a pass from a fail here.
  • A certificate of conformance records the process, measured thickness, alloy content and passivate. Salt spray reports are issued per batch where ordered.

Common Questions

Zinc Nickel Appearance and Alloy FAQ

Answers to the alloy, appearance and specification questions that come up on every zinc nickel order.

Ask a Technical Question
What nickel content is used in zinc nickel plating?

Zinc nickel plating is typically controlled at 12–15% nickel content, depending on the customer specification and the performance target. The nickel band is the defining variable in the deposit, so it is confirmed by measurement on every batch rather than assumed.

How do I specify the appearance of a zinc nickel plated part?

State the nickel band, the coating thickness with its tolerance and measurement points, the post-treatment, and the approved appearance sample the finish is judged against. Appearance follows from that combination, and each of the four has to be fixed for the finish to be unambiguous.

What is the difference between trivalent chromate and a topcoat on zinc nickel plating?

Trivalent chromate is a conversion finish applied over the zinc nickel deposit; a topcoat is an additional layer over the alloy. The choice changes both the appearance and how the surface responds to wear and exposure, so it is called out on the drawing rather than left to the supplier.

Is bake embrittlement relief required for zinc nickel plating?

Yes, on high-strength steel. Bake embrittlement relief is mandatory for steel at or above 1,000 MPa, and Fukar bakes every zinc nickel job on hardened steel as standard, with the bake record included in the certificate of conformance.

How is zinc nickel plating inspected before delivery?

Thickness and alloy composition are verified by XRF on every batch at the points the drawing calls out, appearance is checked against the approved sample, and a certificate of conformance records the process, the measured thickness, the nickel content and the passivate. Salt spray test reports are issued per batch against the specification ordered.

Zinc Nickel Plating

See the zinc nickel service, the ASTM B841 reference and the process flow.

View service →

Zinc Nickel vs Zinc Plating

Compare alloy zinc nickel with standard zinc plating for protection level and application fit.

View comparison →

ASTM B841 Standard

See what the zinc nickel plating standard covers, class by class.

View standard →

Need zinc nickel plating support for your fasteners?

Send the fastener class, the alloy band and the corrosion target. We'll confirm the specification and the inspection evidence before production.